Xintai Superhard Materials is an independent supply partner. Manufacturing is performed by qualified partner factories.
Record 02 / Diamond grinding paste
Specification record · values confirmed at quotation
Diamond grinding paste · W1.5 example
W1.5 oil-soluble is the example configuration shown here. It is a starting point for the conversation, not a fixed stock item: the working grade, carrier and consistency are confirmed against your process and the partner factory’s current datasheet.
01 / At a glance
A concrete starting point: one grade, one carrier and one use category to react to. The detail is confirmed at quotation.
W1.5 oil-soluble gives the quotation a concrete starting point: a grade, a carrier and a use category to test against. It is easier to react to a defined configuration than to a range.
The final configuration is set by your operation. The partner factory’s current datasheet, not this page, is the reference for the grade and tolerance that will actually be supplied.
01 Example grade configuration; final grade, tolerance and packaging confirmed at quotation against the selected partner factory’s current datasheet.
02 / Carrier choice
The carrier changes how the paste behaves at the machine and how the part is cleaned afterwards. Neither option is universally better.
A prepared paste in an oil-based carrier. Often considered where the process already runs oil-based fluids and the cleaning routine can handle an oil residue.
Example: the W1.5 oil-soluble configuration shown on this page.
A paste built around a water-soluble carrier. Often considered where water-based fluids are already in use and the cleaning routine favours water.
Example carrier option; availability and behaviour confirmed with the partner factory.
02 Carrier availability and compatibility are confirmed per order. Neither carrier is presented as a universal recommendation.
03 / Grade series
A working ladder from finer to coarser. The designations show where a conversation might start, not what is guaranteed to be in stock.
Final finishing steps where surface quality leads the decision.
Polishing and fine lapping where the finish target is the constraint.
The starting point used on this page. Confirmed against your process.
Finishing and polishing where some removal still matters.
Intermediate steps before the final finishing stage.
Heavier removal or lapping support before finer grades.
03 Illustrative grade set. Current availability and tolerances are confirmed at quotation against the selected partner factory’s current datasheet. W1.5 oil-soluble is an example configuration, not a stock promise.
04 / Where it is used
These are the questions we ask before proposing a configuration.
Substrate 01
Edge preparation and finishing on carbide inserts, drills and end mills. Grade is matched to the edge condition, and carrier to your cleaning routine.
Read the carbide route →Substrate 02
Lapping and polishing of steel and other precision parts where flatness, finish and repeatability are measured.
Read the precision route →Substrate 03
Hard, brittle substrates where removal and surface damage shift with the step. Carrier compatibility is checked first.
Read the ceramics route →04 Application notes are general process guidance, not performance claims.
05 / Specification record
The table separates an illustrative starting point from information that must be confirmed for the order.
| Field | How it is confirmed |
|---|---|
| Grade system | W-series designations. W1.5 is shown as the example; final designation and tolerance come from the selected partner factory’s current datasheet. |
| Carrier options | Oil-soluble or water-soluble, selected against the machine, cleaning route and process requirements. |
| Use category | Lapping, polishing and edge finishing. Suitability is assessed against your substrate and process. |
| Customisation | Grade, carrier and consistency are specified per order and confirmed by the manufacturing partner. |
| Documentation | Batch documentation is coordinated with the manufacturing partner; no in-house certificates are implied. |
| Packaging | Specified per order and destination, including buyer labels and shipping marks where required. |
05 Source note: selected partner factory’s current datasheet, sample evaluation and the written quotation.
06 / Before dispatch
Each item is agreed in writing; none of it is a certification claim.
Confirmed against the partner factory’s current datasheet and stated on the quotation.
Oil or water base and paste consistency agreed for your machine and process.
Container, label content and shipping marks specified per order and destination.
The document set is coordinated with the manufacturing partner before dispatch.
Destination, paperwork and any third-party inspection coordination agreed before shipment.
If you evaluate a sample, its configuration is written into the order record.
06 Coordination checklist only. Xintai does not operate a manufacturing site or laboratory and does not issue its own test certificates.
07 / Customisation
A sample evaluation, a non-standard carrier or a specific packaging format can be coordinated.
01
A sample can be coordinated through the partner factory so the configuration can be tested on your process before a full order. Availability and any charge are confirmed first.
02
Describe the gap: carrier, consistency, finish target or handling. We take the requirement to the partner factory and come back with what is possible.
03
Packaging is specified per order and destination, including buyer labels, inner packaging and shipping marks where required.
Next step
Tell us the operation, material and finish target. We will come back with a configuration and the documents the partner factory can provide.
